A Practical Guide to Surface Mount Technology (SMT) Covering Solder Paste, Reflow, Components, and Process Control

Solder Paste, Stencils & Workshop Basics

  1. Standard SMT workshop temperature is 25°C ±3°C (77°F ±5.4°F).
  2. Required tools for solder paste printing include: solder paste, stencil, squeegee, stencil wipes, lint-free cloth, cleaning solvent, and a paste spatula.
  3. Common solder paste alloy: Sn/Ag/Cu 305 (96.5/3.0/0.5), melting point: 217°C (422.6°F).
  4. Solder paste contains two main components: solder powder and flux.
  5. The flux removes oxides, breaks surface tension, and prevents re-oxidation during soldering.
  6. Typical volume ratio of solder powder to flux: 1:1; weight ratio: 9:1.
  7. Always follow FIFO (first-in, first-out) when using solder paste. Two required steps before use: bring to room temperature and stir thoroughly.
  8. For moisture-sensitive devices (MSDs), the humidity indicator card (HIC) must show blue to proceed with assembly.
  9. Common stencil manufacturing methods: etching, laser cutting, electroforming, and nano-coating. Among them, laser-cut stencils are reworkable.
  10. SMT stands for Surface Mount Technology – attaching electronic components directly onto the surface of PCBs.

ESD, Components & Documentation

  1. ESD stands for Electrostatic Discharge, a critical factor in electronic manufacturing.

  2. SMT machine programs generally consist of five data sets: PCB data, fiducial mark data, feeder data, nozzle data, and part data.

  3. The relative humidity inside dry cabinets for MSDs should be maintained below 10% RH.

  4. Common passive components: resistors, capacitors, inductors, diodes; common active components: transistors, ICs.

  5. SMT stencils are typically made from stainless steel, with common thicknesses being 0.12 mm or 0.15 mm.

  6. Try to balance cycle times between high-speed and multi-purpose placement machines to optimize line efficiency.

  7. Sources of static charge include friction, separation, induction, and conduction.

    • ESD risks: device failure, contamination.
    • Elimination methods: ionization, grounding, and shielding.
  8. Package sizing:

    • Imperial 0603 = 0.06" × 0.03"
    • Metric 3216 = 3.2 mm × 1.6 mm
  9. Example of component markings:

    • Resistor “ERB-05604-J81”: “4” = 4 circuits, 56Ω
    • Capacitor “ECA-0105Y-M31”: C = 106 pF = 0.1 nF
  10. Document types:

    • ECN = Engineering Change Notice
    • SWR = Special Work Request

    These must be signed off by relevant departments and issued by document control to be valid.

5S & Quality Management

  1. The 5S system stands for: Sort, Set in order, Shine, Standardize, Sustain.
  2. Vacuum-sealed PCB packaging helps protect against dust and moisture.
  3. The “Three No” Quality Policy:
    • No receiving of defects
    • No making of defects
    • No passing on of defects
  4. Quality assurance steps:
    • Understand customer needs
    • Translate needs into standards
    • Train operators
    • Audit and improve continuously
    • Ensure customer satisfaction
  5. In fishbone (Ishikawa) analysis, 4M1H refers to: Man, Machine, Material, Method, and Environment (H = “Huánjìng” in Chinese).

Process Control & Marking Codes

  1. Solder paste composition includes:
    • Metal powder (85–92% by weight)
    • Solvent, flux, anti-slump agent, activators
  2. Before use, refrigerated solder paste must return to room temperature to prevent defects such as solder balling after reflow.
  3. Common SMT feeder modes: Preparation, Priority Exchange, Exchange, and Quick Exchange.
  4. PCB positioning methods in SMT lines include: vacuum, mechanical holes, edge clamping, and side edge guides.
  5. Resistor marking:
    • “272” = 2.7 kΩ
    • “485” = 4.8 MΩ

Quality Metrics & Reflow Profiling

  1. BGA component markings typically include: manufacturer name, part number, specifications, and date/lot code.
  2. True definition of quality: “Getting it right the first time.” QC types: IQC, IPQC, FQC, OQC.
  3. The fishbone diagram in quality control emphasizes cause-and-effect analysis.
  4. CPK (Process Capability Index) represents the real-time performance capability of a process.
  5. Flux starts evaporating and activates chemically in the preheat zone during reflow.
  6. Ideal reflow profiles: cooling curve should mirror heating curve for balanced thermal stress.
  7. Typical reflow soldering profile: Ramp → Soak → Reflow → Cool.
  8. Most commonly used PCB substrate material is FR-4 (flame-retardant fiberglass).
  9. Maximum allowed PCB warpage is 0.75% of the diagonal length.
  10. Uneven heating of components during reflow may cause tombstoning, misalignment, or cold solder joints.

Equipment, Packaging & SMT History

  1. Standard BGA ball diameter used in motherboards: 0.76 mm.
  2. ABS system refers to absolute coordinate systems; high-speed placers can place resistors, capacitors, ICs, transistors.
  3. Ceramic chip capacitor “ECA-0105Y-K31” has a tolerance of ±10%.
  4. Panasonic Panasert SMT machines typically operate at 3-phase, 200V ±10VAC.
  5. SMT tape reel sizes are generally 13-inch and 7-inch diameter.
  6. Stencil apertures are usually 4μm smaller than PCB pad to reduce solder balling.
  7. BIOS = Basic Input/Output System, critical for booting and hardware control.
  8. If an IC moisture indicator card shows humidity >30%, the IC is considered moisture-absorbed and compromised.
  9. Correct solder paste ratio:
    • Weight: 90% solder / 10% flux
    • Volume: 50% solder / 50% flux
  10. SMT originated in the mid-1960s, developed by military and aerospace industries.

Machines, Tools & Production Flow

  1. Paper tape reels with 8mm width usually have a component pitch of 4mm. Note: “20mm” is not a valid carrier tape width.
  2. In early 1970s, HCC referred to a new SMD type: Hermetically Sealed Leadless Chip Carriers.
  3. Component code “272” = 2.7 kΩ resistor; “100nF” capacitor is equivalent to 0.1μF.
  4. Common pick-and-place machines include:
    • In-line,
    • Rotary turret,
    • Gantry-type systems.
  5. Flux types based on rosin include: R, RA, RSA, and RMA.
  6. The most commonly used material for SMT components is ceramic.
  7. SMT repair tools: soldering iron, hot air rework station, desoldering pump, tweezers.
  8. Ideal solder pot temperature during manual soldering: 245°C (473°F).
  9. Basic SMT production flow: Board loader → Solder paste printer → High-speed placer → Multi-purpose placer → Reflow oven → Unloader.
  10. Most PCBs used in current computers are made of fiberglass-reinforced epoxy (FR-4).

Process Parameters & Inspection

  1. Resistor arrays (networks) used in SMT are non-polarized.

  2. Most commercial solder pastes maintain optimal tackiness for ~4 hours after application.

  3. Standard air pressure for SMT equipment: 5 kg/cm² (≈ 71 psi). Placement rule: small components first, larger ones later.

  4. For PCBs with PTH on the top side and SMT on the bottom, use dual-wave soldering with turbulence flow.

  5. Common SMT inspection methods include:

    • Visual inspection
    • X-ray inspection
    • Automated Optical Inspection (AOI)
  6. Heat transfer during soldering iron repairs involves conduction + convection.

  7. Typical BGA solder ball composition: Sn90 / Pb10.

  8. Common stencil fabrication methods: laser cutting, electroforming, chemical etching.

  9. Reflow oven temperature should be set based on actual measurements via thermocouples.

  10. Post-reflow, components are expected to be securely soldered onto the PCB.

Quality Evolution, Testing & Solder Alloys

  1. The evolution of quality management: TQC → TQA → TQM (Total Quality Control → Assurance → Management).
  2. ICT (In-Circuit Testing) uses bed-of-nails fixtures and static testing for components.
  3. Static electricity has low current and is greatly affected by humidity.
  4. Advantages of solder alloys:
    • Lower melting point
    • Good fluidity at low temperatures
    • Meets mechanical strength requirements
  5. If reflow oven components or process settings are changed, temperature profiling must be remeasured.

Equipment, Feeding & Mechanical Systems

  1. Siemens 80F/S system uses electronic drive control.
  2. Solder paste thickness testers use laser measurement to inspect:
    • Paste height
    • Thickness
    • Printed width
  3. Common SMT feeding methods:
    • Vibratory feeders
    • Tray feeders
    • Tape-and-reel feeders
  4. Mechanical structures used in SMT machines include:
    • Cam mechanisms
    • Linkage mechanisms
    • Screw drives
    • Sliding mechanisms
  5. If visual inspection is inconclusive, refer to:
    • BOM file
    • Supplier confirmation
    • Reference board (Golden Sample)

Reflow, Prototyping & Defect Analysis

  1. For packaging marked “12w8P,” adjust pitch counter to 8 mm feed per advance.

  2. Types of reflow ovens include:

    • Hot air reflow
    • Nitrogen reflow
    • Laser reflow
    • Infrared reflow
  3. Sample production methods for SMT prototyping:

    • Inline automation
    • Manual printing + machine placement
    • Manual printing + manual placement
  4. Common fiducial mark shapes:

    • Circle, cross, square, diamond, triangle, swastika
  5. Improper reflow profiling can cause microcracks, especially in preheat or cooling zones.

  6. Main causes of solder balls during reflow:

    • Poor PCB pad design
    • Oversized stencil apertures
    • Over-penetrated component placement
    • Excess paste collapse or low viscosity
    • Excessive ramp rate in reflow profile
  7. Common reasons for solder bridging due to bad stencil printing:

    1. Low metal content → paste collapse
    2. Oversized apertures → too much solder
    3. Poor stencil quality → poor paste release
    4. Residual solder under stencil → reduce squeegee pressure and apply proper vacuum + solvent cleaning
  8. Purpose of each reflow profile zone:

    • Preheat zone: solvent evaporation
    • Soak zone: flux activation, oxidation removal
    • Reflow zone: solder melting
    • Cooling zone: joint solidification and metallurgical bonding